Site: Home > Home > News and events

Air-cooled xenon lamp aging chamber technical parameters

2021-11-05 10:57

Xenon lamp aging test chamber using xenon arc lamp that can simulate the full sunlight spectrum to reproduce the destructive light waves present in different environments, according to the test standards and methods are divided into three kinds are air-cooled xenon lamp, water-cooled xenon lamp, desktop xenon lamp, of which the main difference is the temperature, accuracy, time, humidity, etc., the following xenon lamp aging box manufacturer to give you a detailed introduction to the air-cooled xenon lamp aging tester.

 Air-cooled xenon lamp aging box is also called air-cooled xenon lamp aging box, is a way to use the blowing wind to take away the excess heat emitted by the xenon lamp lamp, its technical difficulty, the device is relatively simple, and the cost is relatively cheaper than the water-cooled xenon lamp aging tester. The aging test chamber in the test chamber on top of the installation of one or more air-cooled xenon lamp.


In this system, its filter is flat, so it is sometimes called a flat xenon lamp aging chamber, the filter is placed in the lower part of the lamp, while the top and side of the test chamber are equipped with a reflection system to enhance the uniformity of irradiance distribution. Samples for testing are placed on a shelf below the lamp. The flat sample compartment is tilted at a slight angle to facilitate the flow of water when spraying or condensing.

Technical parameters of air-cooled xenon lamp aging tester.

Temperature range: RT +10℃~70℃

Humidity range: 65% ~ 98% RH

Black plate temperature: 63 ℃ ~ 100 ℃

Temperature uniformity: ≤ 2.0℃ (when dark)

Temperature fluctuation: ±0.5℃ (when dark)

Humidity deviation:+2、-3% RH

Water spray nozzle aperture: Ф0.8mm

Rainfall water pressure: 0.12~0.15Mpa

Rainfall time: 1 ~ 999M, continuous rainfall adjustable

Spraying cycle: 18min/102min or 12min/48min (spraying time/stopping time)

Light cycle: 1 ~ 999h, m, s continuously adjustable

Sample tray size: 450 × 720mm

Sample holder and lamp distance: 230 ~ 280mm


Radiation intensity: ≤ 550W/㎡

Xenon lamp power: 2.5KW × 3 = 7.5KW

Heating power: 3.0KW

Humidification power: 2.0KW

Outer box material: high-quality A3 steel plate electrostatic spraying

Inner box material: imported senior stainless steel SUS304

Temperature and humidity controller: "Taiwan Willen" touch screen + "Germany Siemens" PLC module

Temperature and humidity sensor: PT100 platinum resistance temperature measurement body

Standard configuration: 3 lamps, sample rack 1 layer

Safety protection: compressor overpressure, compressor overload, water shortage protection, fan motor overheating overall

Equipment over temperature, the overall equipment under-phase / reverse phase, the overall equipment

Overall equipment timing leakage protection, water shortage protection, automatic shutdown after the fault alarm and other protection

Power supply voltage: AC380V±10% 50Hz

Power: 14.5KW

Using environment: 5℃~+28℃ ≤85% RH

Related News

2023-10-26How do you measure oxygen levels in an experiment?
2023-10-26What is ASTM D6413?
2023-10-26What is ASTM D 695 standard test method for compressive properties of rigid plas
2023-10-26What types of construction materials are covered by ASTM standards?
2023-10-25Differences in the testing procedures between ASTM D2863 and ASTM D2863 17
2023-10-25What is the test method for limiting oxygen index?
2023-10-24What is 50% stretch in fabric?
2023-10-24How do you test fabric quality?
2023-10-24How are the materials are tested as per ASTM standards?
2023-10-24Can the oxygen index test be used to compare the fire resistance properties of d

Copyright 2022:Qinsun Instruments Co., Limited

High-end textile tester supplier | Textile Testing Equipment pdf | Tel:021-67800179 |