Site: Home > Home > News and events

How is Sweating Fabric Manikin (Walter) applied?

2021-12-30 11:06

Sweating Fabric Manikin (Walter) played an important role in the physical research and the development of occupational protective clothing. In terms of the structure of the thermal manikin, the testing principle and the application, etc., the thermal manikin is comprehensively connected. Under all wearing conditions, the clothing reduces the heat loss from the human body to the environment. At present, the thermal manikin is widely used in the textile and apparel industry. , The test of all aspects of the user's clothing is very effective.

Sweating Fabric Manikin (Walter) can test detailed data systems. The dummy itself does not have fingers and faces. The dummy has higher strength. A pure nickel wire close to 700m is placed in the dummy from the fingers to the nasal cavity. The independent intelligent circuit guarantees the accuracy of the measurement process. The only circuit in each part ensures the accuracy of the measurement, and the built-in heat conduction system can ensure good uniformity. At the same time, the dummy can be divided into two parts, which is easy to transport.


main application:

In the dangerous environment of the fire field, people need to wear thermal protective clothing to avoid fire damage. Thermal protective clothing is widely used to protect firefighters, steel workers, and workers engaged in other high-temperature hazardous locations. As the clothing is exposed to the flame for an increase in time, the surface temperature of the clothing will gradually increase due to the direct burning of the flame, and a large amount of heat transfer makes the air layer under the clothing and the surface temperature of the human body rise at the same time. Not only will the thermal physical properties of the fabric itself change under the flame burning, which will affect its thermal protection performance, but also after leaving the flash fire environment, the surface temperature of the clothing will still remain in a higher range, and will be in contact with the clothing underneath. And the temperature of the surface of the human body forms a temperature difference, and the continuous heat transfer causes the surface temperature of the human body to continue to rise. Studies have shown that burns may occur after the flash fire is over, and the energy stored in the fabric is also an important factor in predicting burns. Therefore, even if the thermal protective clothing can withstand the flame burning for a short time, the clothing can still cause burns during the cooling process. Therefore, it is particularly important to study the changes in the surface temperature of clothing and human body after burning.

Research on multi-layer protective clothing by QINSUN researchers through Sweating Fabric Manikin (Walter) shows that the outermost fabric has an important influence on the protective performance of multi-layer protective clothing. Using TPP instrument to test, it is found that long-term exposure to a heat source with low heat flux is more likely to cause burns than short-term violent combustion. In the actual wearing process, the thermal protection performance of clothing not only depends on the performance of the fabric itself, but also needs to be comprehensively considered from the aspects of clothing style design, specifications and dressing posture. In order to simulate the situation of the human body in the actual fire field as realistically as possible and to safely and accurately determine the surface temperature of the clothing and the human body, the test method of the burning dummy has shown its advantages and has been widely used in the field of thermal protection.

The above is a detailed explanation of the content of Sweating Fabric Manikin that QINSUN will answer for you. Of course, if you need to purchase, please leave a message and order!

Related News

2023-10-26How do you measure oxygen levels in an experiment?
2023-10-26What is ASTM D6413?
2023-10-26What is ASTM D 695 standard test method for compressive properties of rigid plas
2023-10-26What types of construction materials are covered by ASTM standards?
2023-10-25Differences in the testing procedures between ASTM D2863 and ASTM D2863 17
2023-10-25What is the test method for limiting oxygen index?
2023-10-24What is 50% stretch in fabric?
2023-10-24How do you test fabric quality?
2023-10-24How are the materials are tested as per ASTM standards?
2023-10-24Can the oxygen index test be used to compare the fire resistance properties of d

Copyright 2022:Qinsun Instruments Co., Limited

High-end textile tester supplier | Textile Testing Equipment pdf | Tel:021-67800179 |